Economy DIY Wire Balustrade Kit For Timber Posts

$7.10
Ex Tax: $6.45
  • Brand: Econ
  • Product Code: Kit-Econ-DIY-Timber
  • Availability: 2-3 days

OverView

Economy DIY Wire Balustrade Kit For Timber Posts

Package contains

Saddle (Eye Strap) 5mm Econ AISI 316 Saddle (Eye Strap) 5mm Econ AISI 316 $0.47 x 2
Bottlescrew 5mm Jaw/Jaw Econ AISI 316 Bottlescrew 5mm Jaw/Jaw Econ AISI 316 $4.57 x 1
Thimble Small Eye suits 3.2mm Wire Rope AISI 316 Thimble Small Eye suits 3.2mm Wire Rope AISI 316 $0.23 x 2
Swage Sleeve 3.2mm 1/8" Croc Nickel Plated Copper Swage Sleeve 3.2mm 1/8" Croc Nickel Plated Copper $0.41 x 2
8G x 32mm C/Sunk Philips Self Tapper AISI 304 8G x 32mm C/Sunk Philips Self Tapper AISI 304 $0.08 x 4

Below are optional accessories that are suitable for use with this product

If you would like any of these accessories, enter desired quantities here, then click ADD TO CART button below

Hand Swage Tool Croc 3mm, 4mm & 5mm

Hand Swage Tool Croc 3mm, 4mm & 5mm

$91.45 Ex Tax: $83.14

  • Grand total (including added accessories):

  • Grand total (Ex Tax):

Economy DIY Wire Balustrade Kit For Timber Posts

The Economy DIY Wire Balustrade Kit suits straight and angled sections using timber posts and is a true do-it-yourself kit supplied with stainless steel fittings and wire rope for installation on-site. Although this system has a much more involved and time consuming installation process, it is ideal for those on a strict budget. 



Wire and tools need to be purchased separately, see above.

This kit includes: 

4 x 8g 32mm 304 Screws

2 x Econ 5mm Saddles

1 x Econ M5 Bottlescrew Jaw/Jaw

2 x 3.2mm Thimbles

2 x 3.2mm Swage Sleeves

Order 1 kit per wire run required.  WIRE TO BE PURCHASED SEPARATELY OR VIA THE ACCESSORIES OPTIONS ABOVE 

How To Install Balustrade System 

1 - Mark and drill all 4mm holes at the required spacing. 


2 - Slide one end of your wire through a swage sleeve and guide it around your thimble. Complete the loop by inserting the end of the wire back through the swage sleeve, leaving 2mm of protruding wire. Swage the swage sleeve two times spaced slightly apart using the HS-14CR tool on setting 3. 

3 - Insert a saddle through your loop and mount to your end post using the screws provided.  With the saddle and wire fixed to your end post, pull the wire straight to the inside face of the opposite end post and cut the wire 100mm shorter.  Pass the wire through your pre-drilled intermediate posts and create a loop as per step 2.


4 - Attach a saddle to the opposite end post using timber screws.  Remove the pins from both ends of your bottlescrew by unattaching both rings.  Attach one end of the bottlescrew to the loop in your wire and the opposite end to mounted saddle, reinsert pins and rings.  Adjust tension on the wire by screwing or unscrewing the middle section of the bottlescrew using a ProRig Multi Tool


5 - Lock hex nuts against the body of the bottlescrew to lock the system into place once correct tension is achieved.  For accurate and consistent tension you will require a tension gauge, however you can measure the tension by a deflection test.

 

To view our how to video or find out more about this product view our dedicated DIY System For Timber Posts page.


hiii