CLICK HERE to see our full range of Balustrade Systems.
 


 

ProRig Original Design Nutsert Tension Rod System is one of our most popular streamline DIY stainless steel wire balustrade systems for metal posts. Simply insert the Right Hand Threaded Blind Nut Rivets, or Nutserts, into your metal posts, hand swage the fittings onto each end of your wire then screw into the your posts to create tension on the wire.
 


 

To order, simply measure the overall the distance from inside post to inside post between the starting and finishing points of your posts and provide them to Miami Stainless either through our online Balustrade Builder or contact us directly via phone, fax or email. All the required parts will arrive to your door ready for a very quick and simple installation.

 

For instant online balustrade quotes CLICK HERE

Please Note: This method is only suitable for metal posts.

 

FAQ About This Method

 

Can I install this method myself? Yes, even someone with no experience can easily install all our wire balustrade systems.

 

Do I need any special tools? Other than common handyman tools such as an electric drill and drill bits you will need a Hex Swaging Tool, Soft Jaw Pliers and a set of Wire Rope Cutters. You can purchase these tools and drill bits for easy installation of this system if required.

 

What size and type of stainless steel wire do I use? This method is almost always used with 3.2mm 1 x 19 stainless steel wire rope. This wire is the most functional for stainless steel wire balustrade systems due to its bright surface finish, attractive appearance, durability, strength and low stretch.

 

What spacing do I need between my wires? When using 3.2mm 1 x 19 stainless steel wire, you will usually need 80mm spacing (usually 11 runs) between your wires when using a standard one (1) meter high handrail. Please click here for more information on the current NCC Wire Balustrade Regulations.

 

Can I use this balustrade system on a stair or angled section? No, the Nutsert Tension Rod System cannot be used on a stair or angled section.  However you can use the Jaw Swage Bottlescrew System for metal posts.

 

What size pilot hole should I drill for my Nutserts? You will require a 11.0mm hole to suit the Nutserts.

 

What is the maximum length run I can do? The Nutsert Tension Rod System can easily span up to 6 meters. Longer runs up to 12 meters can be achieved by using a Tensioner at each end, please contact Miami Stainless for further information.

 

What size hole should I drill through my intermediate posts? A 4.0mm hole through your intermediate posts will allow the wire rope pass through.

 

Can I take my balustrade wire around corners? It is not possible with this system to take the balustrade wire around corners.

 

Can I use this method if I have timber posts? No, however the ProRig Original Design Insert Tension Rod System suits timber posts.  You can find out more about the Insert Tension Rod System by clicking the link above.

 

Can I use this method if I have metal posts? Yes.

 

What do I need to get a quote? To get a free, no obligation quote you will need to know how many sections you require and the length of each section. You will also need the height of your handrail between your decking or platform and the underside of your handrail.  You can use the Miami Stainless Balustrade Builder to compare different wire balustrade systems at your convenience or contact us directly.

 

How do I order? Simply follow the steps using the Miami Stainless Balustrade Builder and make a secure payment by credit card or you can contact us directly.

 

If you contact Miami Stainless directly we require your overall wire measurement or the exact measurements from the inside to inside face of your posts to be supplied in writing.  You can provide these measurements by email or fax. At this time payment is required which can be made by either credit card over the phone or by EFT. When making payment by EFT, please email or fax your payment remittance with invoice number to make sure your items are not delayed. Please note: For security reasons, please do not email your credit card details.

 

How much will freight cost me and when can I expect delivery? The Nutsert Tension Rod System is usually dispatched the day* full payment is received.

Free delivery for orders over $500 excl GST*Exclude Western Australia, Nothern Territory and Tasmania - $40 flat fee. Bulky, oversize, or overweight packages may incur extra freight charges. Delivery charges exclude handrail tube – price on application. Delivery times may vary.

Please note: Miami Stainless offers an Air Freight service for packages under 5kg.  Please contact us for further information.

 

*While Miami Stainless endeavors to make sure all stainless steel wire and fittings are dispatched the day payment is made, during busy times such as leading into Christmas, we can experience a high workload and delays. 

 

Destination

Approximate Delivery Time

Queensland

1 2 full working days

New South Wales

1 2 full working days

Australian Capital Territory

1 2 full working days

Victoria

2 3 full working days

South Australia

2 3 full working days

Tasmania

5 6 full working days

Northern Territory

6 7 full working days

Western Australia

6 7 full working days

*Miami Stainless cannot guarantee freight delivery times

 

What should I do if I have any further questions? If you have any further questions please contact Miami Stainless directly on 1800 022 122 or by email, [email protected] and one of our friendly staff will be happy to help.