Trade Discount Available! Register Today.

Cart
nutsert swage stud

Econ Nutsert Swage Stud System For Metal Posts

The Econ Design Nutsert Swage Stud System™ is one of our most popular streamline stainless steel wire balustrade systems for metal posts. Simply insert the Left Hand Threaded and Right Hand Threaded Nutserts in to your metal posts using a Blind Nut Rivet Tool then screw the corresponding factory swaged Swage Studs to create tension on the wire.

To order, simply measure the distance from inside post to inside post between the starting and finishing points of your posts and provide them to Miami Stainless either through our online Balustrade Builder or contact us directly via phone, fax or email. Your wires will arrive to your door pre-swaged to your exact measurements for a very quick and simple installation.

Please Note: This method is only suitable for metal posts.

Shop System

FAQ about Econ Nutsert Swage Stud System For Metal Posts

Can I install this method myself?

Yes, even someone with no experience can easily install all our wire balustrade systems.

Do I need any special tools?

Other than common handyman tools such as an electric drill and drill bits you will need a Blind Nut Rivet or Nutsert Tool with Right Hand and a Left Hand Mandrel assemblies. You can purchase the HN-02 Blind Nut Rivet Tool, Left Hand Threaded Mandrel assembly and drill bits for easy insertion of the Nutserts in to your posts if required.

What size and type of stainless steel wire do I use?

This method is almost always used with 3.2mm 1 x 19 stainless steel wire rope. This wire is the most functional for stainless steel wire balustrade systems due to its bright surface finish, attractive appearance, durability, strength and low stretch.

What spacing do I need between my wires?

When using 3.2mm 1 x 19 stainless steel wire, you will usually need 80mm spacing (usually 11 runs) between your wires when using a standard one (1) meter high handrail. Please click here for more information on the current NCC Wire Balustrade Regulations.

Can I use this balustrade system on a stair or angled section?

No, the Nutsert Swage Stud System cannot be used on a stair or angled section.  However you can use the Jaw Swage Bottlescrew System for metal posts.

What size pilot hole should I drill for my Nutserts?

You will require a 10.0mm hole in your posts to suit the Nutserts.

What is the maximum length run I can do?

The Nutsert Swage Stud System can easily span up to 6 meters. Longer runs up to 12 meters can be achieved depending on your type of metal posts, please contact Miami Stainless for further information.

What size hole should I drill through my intermediate posts?

A 7.5mm hole through your intermediate posts will allow the Swage Stud pass through. Please note: If you are using grommets, the required drill size is 11/32″ at a depth of at least 10mm from each side.

Can I take my balustrade wire around corners?

It is not possible with this system to take the balustrade wire around corners.

Can I use this method if I have timber posts?

No, however the ProRig Original Design Threaded Insert Swage Stud System suits timber posts. You can find out more about the Threaded Insert Swage Stud System by clicking on the link above.

Can I use this method if I have metal posts?

Yes

What do I need to get a quote?

To get a free, no obligation quote you will need to know how many sections you require and the length of each section. You will also need the height of your handrail between your decking or platform and the underside of your handrail. You can use the Miami Stainless Balustrade Builder to compare different wire balustrade systems at your convenience or contact us directly.

How do I order?

Simply follow the steps using the Miami Stainless Balustrade Builder and make a secure payment by credit card or you can contact us directly.

If you contact Miami Stainless directly we require your exact measurements from the inside to inside face of your posts to be supplied in writing.

How much will freight cost me and when can I expect delivery?

The Nutsert Swage Stud System is usually dispatched within 3 full working days* after full payment is received.

Free delivery for orders over $500 excl GST. *Exclude Western Australia, Nothern Territory and Tasmania – $40 flat fee. Bulky, oversize, or overweight packages may incur extra freight charges. Delivery charges exclude handrail tube – price on application. Delivery times may vary.

Please note: Miami Stainless offers an Air Freight service for packages under 5kg. Please contact us for further information.

black nutsert swage stud

Black Nutsert Swage Stud System

The ProRig Original Design Nutsert Swage Stud System™ is one of our most popular streamline stainless steel wire balustrade systems for metal posts. Simply insert the Left Hand Threaded and Right Hand Threaded Nutserts in to your metal posts using a Blind Nut Rivet Tool then screw the corresponding factory swaged Swage Studs to create tension on the wire.

To order, simply measure the distance from inside post to inside post between the starting and finishing points of your posts and provide them to Miami Stainless either through our online Balustrade Builder or contact us directly via phone, fax or email. Your wires will arrive to your door pre-swaged to your exact measurements for a very quick and simple installation.

Please Note: This method is only suitable for metal posts.

Shop System

This video is provided as a general guide to help you understand the installation process for this particular Miami Stainless balustrade system. Installation requirements may vary depending on the specific components or configuration you have ordered. Before drilling any holes or commencing installation, please confirm the details with a Miami Stainless specialist to ensure compatibility with your system.

We appreciate you visiting Miami Stainless. For further assistance or technical support, please contact our team on 07 5576 1234.

FAQ about Black Nutsert Swage Stud System

Can I install this method myself?

Yes, even someone with no experience can easily install all our wire balustrade systems.

Do I need any special tools?

Other than common handyman tools such as an electric drill and drill bits you will need a Blind Nut Rivet or Nutsert Tool with Right Hand and a Left Hand Mandrel assemblies. You can purchase the HN-02 Blind Nut Rivet Tool, Left Hand Threaded Mandrel assembly and drill bits for easy insertion of the Nutserts in to your posts if required.

What size and type of stainless steel wire do I use?

This method is almost always used with 3.2mm 1 x 19 stainless steel wire rope. This wire is the most functional for stainless steel wire balustrade systems due to its bright surface finish, attractive appearance, durability, strength and low stretch.

What spacing do I need between my wires?

When using 3.2mm 1 x 19 stainless steel wire, you will usually need 80mm spacing (usually 11 runs) between your wires when using a standard one (1) meter high handrail. Please click here for more information on the current NCC Wire Balustrade Regulations.

Can I use this balustrade system on a stair or angled section?

No, the Nutsert Swage Stud System cannot be used on a stair or angled section. However you can use the Jaw Swage Bottlescrew System for metal posts.

What size pilot hole should I drill for my Nutserts?

You will require a 10.0mm hole in your posts to suit the Nutserts.

What is the maximum length run I can do?

The Nutsert Swage Stud System can easily span up to 6 meters. Longer runs up to 12 meters can be achieved depending on your type of metal posts, please contact Miami Stainless for further information.

What size hole should I drill through my intermediate posts?

A 7.5mm hole through your intermediate posts will allow the Swage Stud pass through. Please note: If you are using grommets, the required drill size is 11/32″ at a depth of at least 10mm from each side.

Can I take my balustrade wire around corners?

It is not possible with this system to take the balustrade wire around corners.

Can I use this method if I have timber posts?

No, however the ProRig Original Design Threaded Insert Swage Stud System suits timber posts. You can find out more about the Threaded Insert Swage Stud System by clicking on the link above.

Can I use this method if I have metal posts?

Yes.

What do I need to get a quote?

To get a free, no obligation quote you will need to know how many sections you require and the length of each section. You will also need the height of your handrail between your decking or platform and the underside of your handrail. You can use the Miami Stainless Balustrade Builder to compare different wire balustrade systems at your convenience or contact us directly.

How do I order?

Simply follow the steps using the Miami Stainless Balustrade Builder and make a secure payment by credit card or you can contact us directly.

How much will freight cost me and when can I expect delivery?

The Nutsert Swage Stud System is usually dispatched within 3 full working days* after full payment is received.

Free delivery for orders over $500 excl GST. *Exclude Western Australia, Nothern Territory and Tasmania – $40 flat fee. Bulky, oversize, or overweight packages may incur extra freight charges. Delivery charges exclude handrail tube – price on application. Delivery times may vary.

Please note: Miami Stainless offers an Air Freight service for packages under 5kg. Please contact us for further information.

M6 tensioner swage flip toggle

Tensioner Swage Stud System with Flip Toggle

Our Tensioner Swage Stud with Flip Toggle System is a popular streamline stainless steel wire balustrade system that utilises flip toggle instead of a rod terminal. Available to suit both timber and metal posts, the Tensioner Swage Stud System with Flip Toggle is perfect for single straight or stair sections. Please Note: It is not recommended this system be used where corners exist unless the intersecting wires are offset.

To install the Tensioner Swage Stud System with Flip Toggle, pre-drill holes in posts, for flip toggle end drill a 6mm hole in the inside face only and a 9mm hole for the hex head tensioner on both sides of opposide end post. Intermediate posts require a 7.5mm hole. Insert the flip toggle end of the 6mm hole and pull the wire to lock in place. Pass the opposite end of the wire through any intermediate posts and thread into hex head tensioner inside of end post. Use a spanner and 1/4″ allen key to tension wires and lock system into place.

To order, simply measure the outside distance between the starting and finishing points of your posts and provide them to Miami Stainless either through our online Balustrade Builder or contact us directly via phone, fax or email. Your wires will arrive to your door pre-swaged to your exact measurements for a very quick and simple installation.

Please Note: This method is suitable for both timber and metal posts. It is recommended that you use a standard flat washer on each outside face of your posts when installing this system with timber posts.

Shop System
tensioner flip toggle brochure display

Tensioner Swage – Flip Toggle System Instruction Sheet

Installation instructions for the Tensioner Swage Stud – Flip Toggle wire balustrade system.

Download

FAQ about Tensioner Swage Stud System with Flip Toggle

Can I install this method myself?

Yes, even someone with no experience can easily install all our wire balustrade systems.

Do I need any special tools?

Because the Tensioner Swage Stud System arrives at your door pre-made from our factory you will only require common handyman tools such as an electric drill, drill bits and M6 Allen Key. You can purchase drill bits and an Allen Keys from Miami Stainless for easy installation if required.

What size and type of stainless steel wire do I use?

This method is almost always used with 3.2mm 1 x 19 stainless steel wire rope. This wire is the most functional for stainless steel wire balustrade systems due to its bright surface finish, attractive appearance, durability, strength and low stretch.

What spacing do I need between my wires?

When using 3.2mm 1 x 19 stainless steel wire, you will usually need 80mm spacing (usually 11 runs) between your wires when using a standard one (1) meter high handrail. Please click here for more information on the current NCC Wire Balustrade Regulations.

Can I use this balustrade system on a stair or angled section?

Yes, the Tensioner Swage Stud System for timber and metal posts can be used for stair or angled sections when used with Beveled Washers. For more information, please contact Miami Stainless here.

What is the maximum length run I can do?

The Tensioner Swage Stud System can easily span up to 10 meters. Spans of up to 16 meters can be achieved by using a Tensioner at each end, please contact Miami Stainless for further information.

What size hole should I drill through my intermediate posts?

A 7.5mm hole through your intermediate posts will allow the Swage Stud pass through.

Please note: If you are using grommets, the required drill size is 11/32″.

What size hole should I drill through my start and termination posts?

A 7.5mm hole will suit the Rod Terminal end and the M6 Tensioner end will require a 9.0mm hole.

Can I take my balustrade wire around corners?

Miami Stainless highly recommends that you do not bend your wire around corners; this can fatigue the wire, put excessive stress on your posts, and make it difficult to get the required tension on your wire to meet NCC Regulations.

Can I use this method if I have timber posts?

Yes, you can use this system with timber posts. It is recommended that you use a standard flat washer on each outside face of your posts when installing this system with timber posts.

Note: Please advise Miami Stainless if you wish to use this system with timber posts.

Can I use this method if I have metal posts?

Yes, you can use this system with metal posts.

What do I need to get a quote?

To get a free, no obligation quote you will need to know how many sections you require and the length of each section. You will also need the height of your handrail between your decking or platform and the underside of your handrail. You can use the Miami Stainless Balustrade Builder to compare different wire balustrade systems at your convenience or contact us directly here.

How do I order?

Simply follow the steps using the Miami Stainless Balustrade Builder and make a secure payment by credit card or you can contact us directly here.

If you contact Miami Stainless directly we require your exact measurements from the outside to inside face of your posts to be supplied in writing.

10 Jaw Swage Steel Post 031018

ProRig Jaw Swage Bottlescrew System for Metal Posts

Our Jaw Swage Bottlescrew System is one of our most popular streamline stainless steel wire balustrade systems for stair or angled sections. Available to suit both timber and metal posts, the Jaw Swage Bottlescrew System is perfect for high use areas where children, pets or guests may pull on the wires.

To install the Jaw Swage Bottlescrew System into metal posts simply insert the right hand threaded and Blind Nut Rivets or Nutserts into your metal posts, screw in the Eye Bolts, attach the pre-swaged fittings at the end of each wire by siding the pin through the Eye Bolt and create tension by rotating the Bottlescrew using a ProRig C-Spanner.

To order, simply measure the distance from inside post to inside post between the starting and finishing points of your posts and provide them to Miami Stainless either through our online Balustrade Builder or contact us directly via phone, fax or email. Your wires will arrive to your door pre-swaged to your exact measurements for a very quick and simple installation.

Please Note: This method is only suitable for metal posts.

Shop System

ProRig Jaw Swage Bottlescrew System for Metal Posts

View all Products
Product Image
Rapidlock Bottlescrew System For Metal Posts Hex Nut M6 AISI 316 $0.04
Add to Cart View Details
Product Image
General Hardware Bottlescrew 5mm Jaw/Swage suits 3.2mm wire $5.92
Add to Cart View Details
Product Image
General Hardware Fork Terminal 5mm Pin suits 3.2mm Wire ProRig $2.81
Add to Cart View Details
Product Image
Rapidlock Bottlescrew System For Metal Posts Eye Bolt Metal Thread M6 x 20mm ProRig AISI 316 $1.44
Add to Cart View Details
Product Image
Rapidlock Bottlescrew System For Metal Posts Wire Rope 3.2mm 1×19 ProRig AISI 316 per Metre $1.50
Add to Cart View Details

FAQ about ProRig Jaw Swage Bottlescrew System for Metal Posts

Can I install this method myself?

Yes, even someone with no experience can easily install all our wire balustrade systems.

Do I need any special tools?

For metal posts, the Jaw Swage Bottlescrew System requires a Blind Nut Rivet, or Nutsert Tool to fasten the Nutserts to the posts. You can purchase the HN-02 Blind Nut Rivet Tool and drill bits for easy installation of this system if required.

What size and type of stainless steel wire do I use?

This method is almost always used with 3.2mm 1 x 19 stainless steel wire rope. This wire is the most functional for stainless steel wire balustrade systems due to its bright surface finish, attractive appearance, durability, strength and low stretch.

What spacing do I need between my wires?

When using 3.2mm 1 x 19 stainless steel wire, you will usually need 80mm spacing (usually 11 runs) between your wires when using a standard one (1) meter high handrail. Please click here for more information on the current NCC Regulations.

Can I use this balustrade system on a stair or angled section?

Yes, the Jaw Swage Bottlescrew System for metal posts is the most common system used for stair or angled sections.

When using this system for metal posts, what size pilot hole should I drill for my Nutserts?

You will require a 10.0mm hole to suit the Nutserts.

What is the maximum length run I can do?

Both Jaw Swage Bottlescrew Systems can easily span up to 10 meters. Spans of up to 16 meters can be achieved by using a Tensioner at each end, please contact Miami Stainless for further information.

What size hole should I drill through my intermediate posts?

A 7.5mm hole through your intermediate posts will allow the swage stud pass through. Please note: If you are using grommets, the required drill size is 11/32″.

Can I take my balustrade wire around corners?

Miami Stainless highly recommends that you do not bend your wire around corners; this can fatigue the wire, put excessive stress on your posts, and make it difficult to get the required tension on your wire to meet NCC Regulations.

What do I need to get a quote?

To get a free, no obligation quote you will need to know how many sections you require and the length of each section. You will also need the height of your handrail between your decking or platform and the underside of your handrail. You can use the Miami Stainless Balustrade Builder to compare different wire balustrade systems at your convenience or contact us directly.

How do I order?

Simply follow the steps using the Miami Stainless Balustrade Builder and make a secure payment by credit card or you can contact us directly.

If you contact Miami Stainless directly we require your exact measurements from the inside to inside face of your posts to be supplied in writing.

How much will freight cost me and when can I expect delivery?

The Jaw Swage Bottlescrew System is usually dispatched within 3 full working days* after full payment is received.

Free delivery for orders over $500 excl GST. *Exclude Western Australia, Nothern Territory and Tasmania – $40 flat fee. Bulky, oversize, or overweight packages may incur extra freight charges. Delivery charges exclude handrail tube – price on application. Delivery times may vary.

Please note: Miami Stainless offers an Air Freight service for packages under 5kg. Please contact us for further information.

10 Jaw Swage Steel Post 031018

Econ Jaw Swage Bottlescrew System for Metal Posts

Our Jaw Swage Bottlescrew System is one of our most popular streamline stainless steel wire balustrade systems for stair or angled sections. Available to suit both timber and metal posts, the Jaw Swage Bottlescrew System is perfect for high use areas where children, pets or guests may pull on the wires.

To install the Jaw Swage Bottlescrew System into metal posts simply insert the right hand threaded and Blind Nut Rivets or Nutserts into your metal posts, screw in the Eye Bolts, attach the pre-swaged fittings at the end of each wire by siding the pin through the Eye Bolt and create tension by rotating the Bottlescrew using a ProRig C-Spanner.

To order, simply measure the distance from inside post to inside post between the starting and finishing points of your posts and provide them to Miami Stainless either through our online Balustrade Builder or contact us directly via phone, fax or email. Your wires will arrive to your door pre-swaged to your exact measurements for a very quick and simple installation.

Please Note: This method is only suitable for metal posts.

Shop System

Econ Jaw Swage Bottlescrew System for Metal Posts

View all Products
Product Image
General Hardware Fork Terminal 5mm Pin suits 3.2mm Wire Econ $1.18
Add to Cart View Details
Product Image
General Hardware Bottlescrew 5mm Jaw/Swage suits 3.2mm wire $3.03
Add to Cart View Details
Product Image
Rapidlock Bottlescrew System For Metal Posts Eye Bolt Metal Thread M6 x 20mm ProRig AISI 316 $1.44
Add to Cart View Details
Product Image
Rapidlock Bottlescrew System For Metal Posts Hex Nut M6 AISI 316 $0.04
Add to Cart View Details
Product Image
Rapidlock Bottlescrew System For Metal Posts Wire Rope 3.2mm 1×19 ProRig AISI 316 per Metre $1.50
Add to Cart View Details
Product Image
Rapidlock Bottlescrew System For Metal Posts Blind Nut Rivet M6 RHT 0.7 – 4.0mm Grip $0.63
Add to Cart View Details

FAQ about Econ Jaw Swage Bottlescrew System for Metal Posts

Can I install this method myself?

Yes, even someone with no experience can easily install all our wire balustrade systems.

Do I need any special tools?

For metal posts, the Jaw Swage Bottlescrew System requires a Blind Nut Rivet, or Nutsert Tool to fasten the Nutserts to the posts. You can purchase the HN-02 Blind Nut Rivet Tool and drill bits for easy installation of this system if required.

What size and type of stainless steel wire do I use?

This method is almost always used with 3.2mm 1 x 19 stainless steel wire rope. This wire is the most functional for stainless steel wire balustrade systems due to its bright surface finish, attractive appearance, durability, strength and low stretch.

What spacing do I need between my wires?

When using 3.2mm 1 x 19 stainless steel wire, you will usually need 80mm spacing (usually 11 runs) between your wires when using a standard one (1) meter high handrail. Please click here for more information on the current NCC Regulations.

Can I use this balustrade system on a stair or angled section?

Yes, the Jaw Swage Bottlescrew System for metal posts is the most common system used for stair or angled sections.

When using this system for metal posts, what size pilot hole should I drill for my Nutserts?

You will require a 10.0mm hole to suit the Nutserts.

What is the maximum length run I can do?

Both Jaw Swage Bottlescrew Systems can easily span up to 10 meters. Spans of up to 16 meters can be achieved by using a Tensioner at each end, please contact Miami Stainless for further information.

What size hole should I drill through my intermediate posts?

A 7.5mm hole through your intermediate posts will allow the swage stud pass through. Please note: If you are using grommets, the required drill size is 11/32″.

Can I take my balustrade wire around corners?

Miami Stainless highly recommends that you do not bend your wire around corners; this can fatigue the wire, put excessive stress on your posts, and make it difficult to get the required tension on your wire to meet NCC Regulations.

What do I need to get a quote?

To get a free, no obligation quote you will need to know how many sections you require and the length of each section. You will also need the height of your handrail between your decking or platform and the underside of your handrail. You can use the Miami Stainless Balustrade Builder to compare different wire balustrade systems at your convenience or contact us directly.

How do I order?

Simply follow the steps using the Miami Stainless Balustrade Builder and make a secure payment by credit card or you can contact us directly.

If you contact Miami Stainless directly we require your exact measurements from the inside to inside face of your posts to be supplied in writing.

How much will freight cost me and when can I expect delivery?

The Jaw Swage Bottlescrew System is usually dispatched within 3 full working days* after full payment is received.

Free delivery for orders over $500 excl GST. *Exclude Western Australia, Nothern Territory and Tasmania – $40 flat fee. Bulky, oversize, or overweight packages may incur extra freight charges. Delivery charges exclude handrail tube – price on application. Delivery times may vary.

Please note: Miami Stainless offers an Air Freight service for packages under 5kg. Please contact us for further information.

black jaw swage bottlescrew timber system

Black Jaw Swage Bottlescrew System for Timber Posts

Our Jaw Swage Bottlescrew System is one of our most popular streamline stainless steel wire balustrade systems for stair or angled sections. Available to suit both timber and metal posts, the Jaw Swage Bottlescrew System is perfect for high use areas where children, pets or guests may pull on the wires.

To install the Jaw Swage Bottlescrew System into timber posts simply screw the supplied Screw Eyes into your timber posts, attach the pre-swaged fittings at the end of each wire by siding the pin through the Screw Eye and create tension by rotating the Bottlescrew using a ProRig C-Spanner.

To order, simply measure the distance from inside to inside post between the starting and finishing points of your posts and provide them to Miami Stainless either through our online Balustrade Builder or contact us directly via phone, fax or email. Your wires will arrive to your door pre-swaged to your exact measurements for a very quick and simple installation.

Please Note: This method is suitable for both timber and metal posts.

Shop System

FAQ about Black Jaw Swage Bottlescrew System for Timber Posts

Can I install this method myself?

Yes, even someone with no experience can easily install all our wire balustrade systems.

Do I need any special tools?

For timber posts, the Jaw Swage Bottlescrew System does not need any specialist tools other then common handyman tools such as an electric drill and 4.0mm drill bit.  You can also purchse our Screw Eye Drive Bit which allows for easier installation of the Screw Eyes into your timber posts.

What size and type of stainless steel wire do I use?

This method is almost always used with 3.2mm 1 x 19 stainless steel wire rope. This wire is the most functional for stainless steel wire balustrade systems due to its bright surface finish, attractive appearance, durability, strength and low stretch.

What spacing do I need between my wires?

When using 3.2mm 1 x 19 stainless steel wire, you will usually need 80mm spacing (usually 11 runs) between your wires when using a standard one (1) meter high handrail. Please click here for more information on the current NCC Regulations.

Can I use this balustrade system on a stair or angled section?

Yes, the Jaw Swage Bottlescrew System for timber and metal posts is the most common system used for stair or angled sections.

When using this system for timber posts, what size pilot hole should I drill for my Screw Eyes?

You will require a 4.0mm pilot hole to suit the Screw Eyes.

What is the maximum length run I can do?

Both Jaw Swage Bottlescrew Systems can easily span up to 10 meters. Spans of up to 16 meters can be achieved by using a Tensioner at each end, please contact Miami Stainless for further information.

What size hole should I drill through my intermediate posts?

A 7.5mm hole through your intermediate posts will allow the Swage Stud pass through. Please note: If you are using grommets, the required drill size is 11/32″.

 

Can I take my balustrade wire around corners?

Miami Stainless highly recommends that you do not bend your wire around corners; this can fatigue the wire, put excessive stress on your posts, and make it difficult to get the required tension on your wire to meet NCC Regulations.

What do I need to get a quote?

To get a free, no obligation quote you will need to know how many sections you require and the length of each section. You will also need the height of your handrail between your decking or platform and the underside of your handrail.  You can use the Miami Stainless Balustrade Builder to compare different wire balustrade systems at your convenience or contact us directly.

How do I order?

Simply follow the steps using the Miami Stainless Balustrade Builder and make a secure payment by credit card or you can contact us directly.

How much will freight cost me and when can I expect delivery?

The Black Jaw Swage Bottlescrew System is usually dispatched within 3 full working days* after full payment is received.

Free delivery for orders over $500 excl GST. *Exclude Western Australia, Nothern Territory and Tasmania – $40 flat fee. Bulky, oversize, or overweight packages may incur extra freight charges. Delivery charges exclude handrail tube – price on application. Delivery times may vary.

Please note: Miami Stainless offers an Air Freight service for packages under 5kg. Please contact us for further information.

rapidlock timber

RapidLock Bottlescrew System for Timber Posts

The Modern Solution for Timber Balustrade Installation

The RapidLock Bottlescrew System is Australia’s most innovative stainless steel wire balustrade solution for timber posts, featuring our patented swageless RapidLock terminal. This revolutionary system eliminates traditional swaging, making timber post installations faster, easier and more flexible than ever before.

Why Choose RapidLock for Timber Posts?

Unlike conventional swaged wire systems, RapidLock’s swageless design gives you complete control over wire tensioning and the flexibility to adjust or release your balustrade whenever needed. Perfect for timber posts, the RapidLock Bottlescrew creates a sleek, professional finish whilst offering installation simplicity that saves you time and money.

The system suits both straight sections and staircase applications on timber posts. Simply install the RapidLock terminal at one end, thread your stainless steel wire through your posts, then secure and tension using the Bottlescrew fitting. No special tools or pre-manufacturing required.

Perfect for:

  • Timber post balustrades
  • Horizontal or vertical wire configurations
  • Residential and commercial applications
  • Decking and outdoor timber structures
  • Projects requiring installation flexibility

RapidLock delivers the precision and durability of stainless steel balustrade systems with modern installation flexibility. Transform your timber post installations with the swageless solution that puts control back in your hands.

Shop System

RapidLock Bottlescrew System for Timber Posts

View all Products
Product Image
Rapidlock Bottlescrew System For Metal Posts Wire Rope 3.2mm 1×19 ProRig AISI 316 per Metre $1.50
Add to Cart View Details
Product Image
RapidLock Bottlescrew System for Timber Posts Rapid Lock Bottlescrew 5mm Jaw/Swagless suits 3.2mm wire $14.97
Add to Cart View Details
Product Image
RapidLock Bottlescrew System for Timber Posts Rapid Lock Swageless Fork Terminal 5mm Pin suits 3.2mm Wire $10.16
Add to Cart View Details
Product Image
Screws Screw Eye 6mm x 60mm ProRig AISI 316 $2.00
Add to Cart View Details
lag bottlescrew system

Econ Lag Swage Bottlescrew System

Our Lag Swage Bottlescrew System is a streamline stainless steel wire balustrade systems for straight sections when using timber posts. To install the Lag Swage Bottlescrew System into timber posts, simply screw the Lag Screw and Lag Bottlescrew into your timber posts, thread the swage stud through any intermediate posts, attach the pre-swaged fittings to the Lag Bottlescrew and create tension by rotating the Bottlescrew. Please Note: It is recommended you use the extra Lag Screws supplied to pre-thread the hole before screwing in the Lag Swage Bottlescrew fittings.

To order, simply measure the distance from inside post to inside post between the starting and finishing points of your posts and provide them to Miami Stainless either through our online Balustrade Builder or contact us directly via phone, fax or email. Your wires will arrive to your door pre-swaged to your exact measurements for a very quick and simple installation.

Please Note: This method is suitable for both timber posts.

Shop System

lag swage bottlescrew brochure display

Lag Swage Bottlescrew System Instruction Sheet

Installation instructions for the Lag Swage Bottlescrew wire balustrade system.

Download

FAQ about Econ Lag Swage Bottlescrew System

Can I install this method myself?

Although the Lag Screw System looks easy to install, it is not recommended for use if you have limited experience installing a Lag Screw System.

Do I need any special tools?

Because the Lag Screw System arrives at your door pre-made from our factory you do not require any special tools.

What size and type of stainless steel wire do I use?

This method is almost always used with 3.2mm 1 x 19 stainless steel wire rope. This wire is the most functional for stainless steel wire balustrade systems due to its bright surface finish, attractive appearance, durability, strength and low stretch.

What spacing do I need between my wires?

When using 3.2mm 1 x 19 stainless steel wire, you will usually need 80mm spacing (usually 11 runs) between your wires when using a standard one (1) meter high handrail. Please click here for more information on the current NCC Wire Balustrade Regulations.

Can I use this balustrade system on a stair or angled section?

Yes, you can use the Lag Screw System on stair or angled sections.

What is the maximum length run I can do?

Our Lag Screw System can easily span up to 8 meters.

What size hole should I drill through my intermediate posts?

A 7.5mm hole through your intermediate posts will allow the Swage Stud pass through. Please note: If you are using grommets, the required drill size is 11/32″.

Can I take my balustrade wire around corners?

Miami Stainless highly recommends that you do not bend your wire around corners; this can fatigue the wire, put excessive stress on your posts, and make it difficult to get the required tension on your wire to meet NCC Regulations.

Can I use this method if I have timber posts?

Yes, you can use this system with timber posts.

Can I use this method if I have metal posts?

No, however the Jaw Swage Bottlescrew System with ProRig Flip Toggle is recommended for use with metal posts

What do I need to get a quote?

To get a free, no obligation quote you will need to know how many sections you require and the length of each section. You will also need the height of your handrail between your decking or platform and the underside of your handrail. You can use the Miami Stainless Balustrade Builder to compare different wire balustrade systems at your convenience or contact us directly.

How do I order?

Simply follow the steps using the Miami Stainless Balustrade Builder and make a secure payment by credit card or you can contact us directly.

If you contact Miami Stainless directly we require your exact measurements from the inside to inside face of your posts to be supplied in writing.

How much will freight cost me and when can I expect delivery?

The Lag Screw System is usually dispatched within 3 full working days* after full payment is received.

Free delivery for orders over $500 excl GST. *Exclude Western Australia, Nothern Territory and Tasmania – $40 flat fee. Bulky, oversize, or overweight packages may incur extra freight charges. Delivery charges exclude handrail tube – price on application. Delivery times may vary.

Please note: Miami Stainless offers an Air Freight service for packages under 5kg. Please contact us for further information.

lag screw swage stud

Econ Lag Screw Swage System

Miami Stainless does not recommend the use of this stainless steel wire balustrade system to inexperienced installers.

Our Lag Screw System is a streamline stainless steel wire balustrade systems for straight, stair or angled sections when using timber posts. To install the Lag Screw Swage System into your timber posts, simply pass one end of the Lag Screw System through any intermediate posts and screw each Lag Screw simultaneously into your posts to create tension. Please note: It is recommended you use two people for installation of this system. It is very important each Lag Screw is tensioned at the same time.  It is also recommended the holes in the timber posts are pre-threaded with the extra supplied Lag Screws.

To order, simply measure the distance from inside to inside post between the starting and finishing points of your posts and provide them to Miami Stainless either through our online Balustrade Builder or contact us directly via phone, fax or email. Your wires will arrive to your door pre-swaged to your exact measurements for a very quick and simple installation.

Please Note: This method is suitable for timber posts.

Shop System
lag screw swage brochure display

Lag Screw Swage Stud System Instruction Sheet

Installation instructions for the Lag Screw Swage Stud wire balustrade system.

Download

FAQ about Econ Lag Swage System

Can I install this method myself?

Although the Lag Screw System looks easy to install, it is not recommended for use if you have limited experience installing a Lag Screw System.

Do I need any special tools?

Because the Lag Screw System arrives at your door pre-made from our factory you do not require any special tools.

What size and type of stainless steel wire do I use?

This method is almost always used with 3.2mm 1 x 19 stainless steel wire rope. This wire is the most functional for stainless steel wire balustrade systems due to its bright surface finish, attractive appearance, durability, strength and low stretch.

What spacing do I need between my wires?

When using 3.2mm 1 x 19 stainless steel wire, you will usually need 80mm spacing (usually 11 runs) between your wires when using a standard one (1) meter high handrail. Please click here for more information on the current NCC Wire Balustrade Regulations.

Can I use this balustrade system on a stair or angled section?

Yes, you can use the Lag Screw System on stair or angled sections.

What is the maximum length run I can do?

Our Lag Screw System can easily span up to 8 meters.

What size hole should I drill through my intermediate posts?

A 7.5mm hole through your intermediate posts will allow the Swage Stud pass through. Please note: If you are using grommets, the required drill size is 11/32″.

Can I take my balustrade wire around corners?

Miami Stainless highly recommends that you do not bend your wire around corners; this can fatigue the wire, put excessive stress on your posts, and make it difficult to get the required tension on your wire to meet NCC Regulations.

Can I use this method if I have timber posts?

Yes, you can use this system with timber posts.

Can I use this method if I have metal posts?

No, however the Jaw Swage Bottlescrew System with ProRig Flip Toggle is recommended for use with metal posts

What do I need to get a quote?

To get a free, no obligation quote you will need to know how many sections you require and the length of each section. You will also need the height of your handrail between your decking or platform and the underside of your handrail. You can use the Miami Stainless Balustrade Builder to compare different wire balustrade systems at your convenience or contact us directly.

How do I order?

Simply follow the steps using the Miami Stainless Balustrade Builder and make a secure payment by credit card or you can contact us directly.

If you contact Miami Stainless directly we require your exact measurements from the inside to inside face of your posts to be supplied in writing.

How much will freight cost me and when can I expect delivery?

The Lag Screw System is usually dispatched within 3 full working days* after full payment is received.

Free delivery for orders over $500 excl GST. *Exclude Western Australia, Nothern Territory and Tasmania – $40 flat fee. Bulky, oversize, or overweight packages may incur extra freight charges. Delivery charges exclude handrail tube – price on application. Delivery times may vary.

Please note: Miami Stainless offers an Air Freight service for packages under 5kg. Please contact us for further information.

jaw swage bottlescrew

Econ Jaw Swage Bottlescrew System for Timber Posts

Our Jaw Swage Bottlescrew System is one of our most popular streamline stainless steel wire balustrade systems for stair or angled sections. Available to suit both timber and metal posts, the Jaw Swage Bottlescrew System is perfect for high use areas where children, pets or guests may pull on the wires.

To install the Jaw Swage Bottlescrew System into timber posts simply screw the supplied Screw Eyes into your timber posts, attach the pre-swaged fittings at the end of each wire by siding the pin through the Screw Eye and create tension by rotating the Bottlescrew using a ProRig C-Spanner.

To order, simply measure the distance from inside to inside post between the starting and finishing points of your posts and provide them to Miami Stainless either through our online Balustrade Builder or contact us directly via phone, fax or email. Your wires will arrive to your door pre-swaged to your exact measurements for a very quick and simple installation.

Please Note: This method is suitable for both timber and metal posts.

Shop System

For hard timber drill a 4.5mm hole*

FAQ about Econ Jaw Swage Bottlescrew System for Timber Posts

Can I install this method myself?

Yes, even someone with no experience can easily install all our wire balustrade systems.

Do I need any special tools?

For timber posts, the Jaw Swage Bottlescrew System does not need any specialist tools other then common handyman tools such as an electric drill and 4.0mm drill bit. You can also purchse our Screw Eye Drive Bit which allows for easier installation of the Screw Eyes into your timber posts.

What size and type of stainless steel wire do I use?

This method is almost always used with 3.2mm 1 x 19 stainless steel wire rope. This wire is the most functional for stainless steel wire balustrade systems due to its bright surface finish, attractive appearance, durability, strength and low stretch.

What spacing do I need between my wires?

When using 3.2mm 1 x 19 stainless steel wire, you will usually need 80mm spacing (usually 11 runs) between your wires when using a standard one (1) meter high handrail. Please click here for more information on the current NCC Regulations

Can I use this balustrade system on a stair or angled section?

Yes, the Jaw Swage Bottlescrew System for timber and metal posts is the most common system used for stair or angled sections.

When using this system for timber posts, what size pilot hole should I drill for my Screw Eyes?

You will require a 4.0mm pilot hole to suit the Screw Eyes.

What is the maximum length run I can do?

Both Jaw Swage Bottlescrew Systems can easily span up to 10 meters. Spans of up to 16 meters can be achieved by using a Tensioner at each end, please contact Miami Stainless for further information.

What size hole should I drill through my intermediate posts?

A 7.5mm hole through your intermediate posts will allow the Swage Stud pass through. Please note: If you are using grommets, the required drill size is 11/32″.

Can I take my balustrade wire around corners?

Miami Stainless highly recommends that you do not bend your wire around corners; this can fatigue the wire, put excessive stress on your posts, and make it difficult to get the required tension on your wire to meet NCC Regulations.

Can I use this method if I have metal posts?

Yes, you can use this system with metal posts by inserting Blind Nut Rivets and Eye Bolts into your metal posts.

What do I need to get a quote?

To get a free, no obligation quote you will need to know how many sections you require and the length of each section. You will also need the height of your handrail between your decking or platform and the underside of your handrail. You can use the Miami Stainless Balustrade Builder to compare different wire balustrade systems at your convenience or contact us directly.

How do I order?

Simply follow the steps using the Miami Stainless Balustrade Builder and make a secure payment by credit card or you can contact us directly. If you contact Miami Stainless directly we require your exact measurements from the inside to inside face of your posts to be supplied in writing

How much will freight cost me and when can I expect delivery?

The Jaw Swage Bottlescrew System is usually dispatched within 3 full working days* after full payment is received.

Free delivery for orders over $500 excl GST. *Exclude Western Australia, Nothern Territory and Tasmania – $40 flat fee. Bulky, oversize, or overweight packages may incur extra freight charges. Delivery charges exclude handrail tube – price on application. Delivery times may vary.

Please note: Miami Stainless offers an Air Freight service for packages under 5kg. Please contact us for further information.

Unable to Add to Cart

×